We’ve upgraded Alisouq for a faster, smoother experience
We’ve upgraded Alisouq for a faster, smoother experience
SKU: 08933311 08933313 08933316 08933312
(incl. VAT)
loading...
Excellent resistance to chemicals Can also be used in critical areas in which the seal comes into contact with various liquids Outstanding resistance to engine oil and transmission oil, refrigerant and anti-freeze agent Non-acidic hardening system Non-corrosive, therefore has no negative impact on electronic components and on lambda probes Sealant in compressed-air can Easy to dispense without additional aids The fine beads allow the product to be applied uniformly Notice When sealing e.g. oil pans and gearboxes it is vital that no sealant gets into the interior. For this reason we recommend to apply the sealant on a joining part surface. Join both parts and then carefully press by hand and lightly slide against each other. Afterwards separate the parts again and then remove the sealant that has gone inside. Join the components again within a max. of 5 minutes and tighten firmly. Before commissioning, observe the hardening time (depending on the sealant thickness). The usage instructions are recommendations based on the tests we have conducted and are based on our experience, carry out your own tests before each application. We do not assume any liability for a specific application result due to the large number of applications and storage and processing conditions. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.
Super RTV silicone adhesive and sealing compound High-quality adhesive and sealing compound for use in industry and the automotive sector. Contents: 200 ml Chemical basis: Neutral crosslinked silicones, oxime-based Smell/fragrance: Characteristic Density: 1.25 g/cm Min. skin-formation time: 5 min Conditions for skin-formation time: at 23C and 50% relative humidity Full curing speed: 3 mm/d Fully hardening/curing conditions: 23C and 50% relative humidity Min. tensile strength: 2.2 N/mm Conditions for tensile strength: in accordance with ASTM D-412 Heat conductance ?: 0.2 J/(m*s*K) Heat conductance ? conditions: in accordance with ASTM D-2214/70 Coefficient of thermal expansion: 0.0002 1/K Coefficient of thermal expansion conditions: in accordance with ASTM EB-31 Dielectric strength: 16 kV/mm Dielectric strength conditions: in accordance with ASTM D-149 Relative permittivity: 2.8 Conditions for relative permittivity: 1 MHz, ASTM D-150 Loss factor: 0.002 Loss factor conditions: 1 MHz, ASTM D-150 Specific volume resistivity: 1000000000000000 Ohm/cm Conditions for specific volume resistivity: in accordance with ASTM D-257 show more ... show less ...
Excellent resistance to chemicals Can also be used in critical areas in which the seal comes into contact with various liquids Outstanding resistance to engine oil and transmission oil, refrigerant and anti-freeze agent Non-acidic hardening system Non-corrosive, therefore has no negative impact on electronic components and on lambda probes Sealant in compressed-air can Easy to dispense without additional aids The fine beads allow the product to be applied uniformly Notice When sealing e.g. oil pans and gearboxes it is vital that no sealant gets into the interior. For this reason we recommend to apply the sealant on a joining part surface. Join both parts and then carefully press by hand and lightly slide against each other. Afterwards separate the parts again and then remove the sealant that has gone inside. Join the components again within a max. of 5 minutes and tighten firmly. Before commissioning, observe the hardening time (depending on the sealant thickness). The usage instructions are recommendations based on the tests we have conducted and are based on our experience, carry out your own tests before each application. We do not assume any liability for a specific application result due to the large number of applications and storage and processing conditions. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.